Get Your Gutters Cleaned Before Autumn Leaves Fall

It may only be the third week of August, but soon we will be seeing the early signs of autumn. Do you know what that means? Every homeowner’s favorite job, leaf maintenance, is right around the corner.

Over the next two months, leaves, branches, and other debris will begin falling onto your roof and down into your gutters, building up over time. As winter approaches, this buildup can contribute to the formation of ice dams, a heavy mass of ice that settles on the edge of your roof where the gutters are installed.

The main job of a gutter is to create a pathway for water to move away from your home and through a downspout to deposit in a safe place away from your home’s foundation. This system is vital to a house; it makes sure water can flow freely and not cause leaks in your roof, attic, and walls. But if your gutters are blocked up, the water has nowhere to go and has no choice but to flow over, creeping up into your roof shingles and down through your siding. This kind of damage is both costly to repair and entirely preventable - so get your gloves on and let’s get to it.

To give your gutters a good clean you’ll need a ladder, a lawn bag or bucket, a small hand rake (or scoop) and a hose. Don’t be tempted to spray debris down the downspout with water; it’s likely that branches and leaves will get stuck inside, clogging it up and leaving you with a whole new mess to deal with.  Start at the downspout opening and work your way backward, collecting gunk away from the downspout and disposing it into your bucket. Work in small sections and don’t let your bag get too heavy – it could throw you off balance and land you in the emergency room.

While you’re making your way around the house, check for any gutter damage, such as sections coming loose. You want to make sure you get those fixed while the weather is good. Once you’ve finished the cleaning, you can give each section a good spray with the hose to check and make sure the water is running through and you don’t have any hidden build-up in those downspouts.

If gutter cleaning is a job you’d rather not take on, hire a contractor to complete the maintenance and then speak to them about putting gutter guards on your home. These wire or mesh overlays are installed on top of the gutter and prevent debris from entering the channel in the first place. They offer a great solution to a messy job and will provide you with peace of mind for years to come. You’ll want to get them installed now before the first signs of autumn to make sure your home is prepared for the onset of fall leaves.

Bob O’Donnell is the owner of O’Donnell Bros. Inc., a Bristol-based home improvement company established in 1975. Email your questions to info@odonnellbros.com with the subject line “Ask the Pro.” All questions may be considered for publication. To contact Bob for your remodeling needs, call O’Donnell Bros. Inc. at (860) 589-5155 or visit http://www.odonnellbros.com. Advice is for guidance only.

What To Look For When Shopping For an Energy Efficient Entry Door

Many people don’t give much thought to their front door, which is surprising considering that it both sets the tone for a home and is a huge contributor to its overall comfort level.

If you’re in the market for a new entry door, there are a lot of factors to take into consideration beyond just color and style. I’m a huge fan of energy efficiency and all too often, I see homeowners losing massive amounts of hot and cold air through ill-fitting old doors with little insulation. Luckily, consumers have some great resources in their corner which can make choosing a new door a real breeze.

Energy performance is often measured by ENERGY STAR®, the symbol created by the Environmental Protection Agency to measure energy efficiency here in the United States. Another label you may see is from the National Fenestration Rating Council (NFRC), which independently tests and certifies products to give consumers more transparency around efficiency. Both of these rating systems rely on several vital performance contributors that you’ll want to pay attention to. Let’s take a closer look.

1. U-Factor measures how well the product keeps heat from escaping a room, which is vital to our cold winters. It’s important to look for a low number here, which identifies a high performing product. Ratings generally range from 0.20-1.20.

2. Solar Heat Gain Coefficient or (SHGC) measures the opposite. This rating helps a homeowner to know how well a product can resist heat gain, which is crucial in the summer. Again, the lower the number, the better - with 0-1 being the range for this measurement.

3. Air Leakage is exactly what it sounds like and if you’ve ever stood next to a door with worn weatherstripping, you’ll know how important it is. Look for a product with a low air leakage rating, generally expressed in units of cubic feet per minute per square foot of the frame area (cfm/ft2). This measure is also highly dependent on the installation of the product, so having a knowledgeable installer is critical.

4. Sunlight is another important factor which is measured through Visible Transmittance or VT. VT is a fraction of the visible spectrum of sunlight that is transmitted through the glazing of a door and weighted by the sensitivity of the human eye. This is measured in nanometers on a scale of 0 to 1. The lower the number, the less the light is transmitted.

5. Finally, Light-to-Solar Gain (LSG) is the ratio of SHGC to VT and helps homeowners understand how light is transmitted relative to heat gain. The higher the number, the more light that is transmitted without adding heat. This number isn’t always provided but can be useful depending on the positioning of your door and its exposure to the sun.

Don’t forget, exterior doors should look great, but their key function is to provide a barrier against the elements. When you’re shopping for one, keep these factors in the forefront of your mind and you’ll be taking all the steps necessary to maintain your family’s comfort for years to come.

Bob O’Donnell is the owner of O’Donnell Bros. Inc., a Bristol-based home improvement company established in 1975. Email your questions for Bob to info@odonnellbros.com with the subject line “Ask the Pro.” All questions may be considered for publication. To contact Bob for your remodeling needs, call O’Donnell Bros. Inc. at (860) 589-5155 or visit http://www.odonnellbros.com. Advice is for guidance only.

Build Your Own Backyard Fire Pit This Weekend

Last week we talked about the different ways you can enjoy an ambient fire in your own backyard. While there are many options for a portable, moveable (and tippable!) pit, many of us like the idea of a permanent area to enjoy evenings gathered around the warm glow of an open fire. So today, I’ll be showing you how to build a simple backyard pit that you can enjoy for the rest of the summer and right through the autumn too.

First things first, always check your town’s website or fire department for their rules on open fires. Some special requirements might include fire size, setback distances, or general fire permits, so make the call before you get started.

Next, choose a place with plenty of room that’s well away from your home and any low hanging trees, bushes, or vegetation. This is a fire we are talking about, so safety has to be of the utmost importance. Also, if you have to dig, make sure you steer clear of any utility lines or in-ground sprinklers.

Once you have your spot, measure out the space for your pit. You’ll want to have 36-44 inches for the inside where the fire will burn, plus an additional 12 inches around for your stone or brick wall. Put a few chairs about 24 inches from where your outer rim will be to ensure that people can fit comfortably without burning their knees. Setting up your space is important - you want to make sure you have enough room for your family to enjoy the fire without the set up feeling too close or crowded.

Once your setup is ready, dig a 12-inch deep hole into the ground. If you’re building your pit on a patio, you’ll want to remove the original pavers. Then add a layer of sand and tamp it down so it’s level. Alternatively, you can also add a layer of additional pavers on top of the current base and fill in the cracks and crevices with sand. It’s important to have this base for your fire to ensure that you protect the ground or your current patio from heat damage.

Next, it’s time to lay your ring. Most home improvement stores carry pre-made fire pit “kits” which include the stone that you’ll need for the job. Alternatively, you can find rounded pavers to purchase at a simple per unit price, just be sure that they are heat resistant. I highly recommend going with a height of at least 18 inches or roughly knee height to ensure that the fire is properly contained while still giving it room to throw heat.

If you’re going with a DIY option, the easier way to do it is to lay the pavers subway style, with each layer centered over the seam of the previous layer to give it extra stability. It also gives the pit a higher-end look. Depending on the size of your pavers, three layers of stone should do the trick. If you’re using brick, you’ll probably need to double that amount.

And that’s it! Of course, you can choose to create a much more lavish design, but if you’re going for a simpler look, it can be built in just a few hours and will be ready to be enjoyed that very day. I can’t wait to see what you come up with. Send me a message on Facebook at facebook.com/odonnellbros to share your ideas.

Bob O’Donnell is the owner of O’Donnell Bros. Inc., a Bristol-based home improvement company established in 1975. Email your questions for Bob to info@odonnellbros.com with the subject line “Ask the Pro.” All questions may be considered for publication. To contact Bob for your remodeling needs, call O’Donnell Bros. Inc. at (860) 589-5155 or visit http://www.odonnellbros.com. Advice is for guidance only.