Your Winter Water Heater Tune-Up Guide

Your Winter Water Heater Tune-Up Guide

When the cold creeps in and the snow starts to pile up, there’s nothing worse than realizing your hot shower just turned into an arctic plunge. Winter is hard enough without water heater problems and the good news is, a little preventative maintenance now can save you from a mid-January cold-water crisis later. Here are a few easy, DIY-friendly steps to keep your water heater running efficiently all season long.

1. Give It a Little Elbow Room

Your water heater works best when it can breathe. Head down to the basement and make sure there’s at least two feet of clearance around the unit. Over time, storage boxes, paint cans, or the kids’ old hockey gear tend to creep closer. Clear that space so air can circulate and you have easy access for inspection and maintenance.

2. Check the Temperature Setting

If you’ve never looked at your water heater’s thermostat, now’s the time. Set it to 120°F - that’s the sweet spot for most homes. Any higher and you risk scalding (especially if you have little ones), plus you’ll waste energy heating water hotter than you need. Any lower and you might invite bacteria to grow. It’s a quick twist of a dial that can make a big difference in comfort and safety.

3. Flush Out Sediment (It’s Easier Than It Sounds)

Connecticut’s water tends to be mineral-rich, which means sediment can build up in the tank over time. That layer of grit forces your heater to work harder and can even make popping or rumbling noises. To flush it:

• Turn off the power (or gas supply).

• Attach a garden hose to the drain valve at the bottom.

• Run the other end to a floor drain or outside.

• Open the valve and let the tank drain until clear.

If it’s been years since your last flush, you may need to repeat the process. This simple step can extend the life of your heater and improve efficiency. Just make sure you close the valve tightly when you’re done.

4. Insulate for Efficiency

Your hot water heater loses heat through its tank and pipes, especially if it lives in a chilly basement. Wrapping it in an insulating blanket (available at any hardware store) can help retain warmth, meaning your system doesn’t have to work as hard.

Also insulate the first six feet of hot and cold water pipes coming from the tank. Foam pipe sleeves are inexpensive and take just minutes to install. It’s one of those small upgrades that pays for itself fast in energy savings.

5. Test the Pressure Relief Valve

This valve is a key safety feature that releases pressure if the tank gets too hot. To test it, place a bucket under the discharge pipe, then lift the valve’s lever gently. You should hear water or air escape briefly. If nothing happens, or it leaks afterward, it’s time to replace the valve. Don’t skip this one; it’s a simple check that can prevent dangerous pressure buildup.

6. Mind the Anode Rod

Your water heater’s anode rod is like a sacrificial hero - it attracts corrosive minerals so your tank doesn’t rust. But it wears out over time. Every few years, check it by unscrewing the hex head at the top of the tank (you might need a socket wrench). If the rod looks thin or coated in calcium, replace it. It’s a $20 part that can add years to your heater’s life.

7. Keep an Eye Out for Trouble Signs

Rusty water, strange noises, or puddles around the base of your heater are all warning flags. A little condensation on cold days is normal but leaks are not. If you see rust or corrosion near fittings, or your water takes longer to heat up, call in a professional before winter really sets in.

8. Know When to Call the Pros

While most of these steps are DIY-friendly, there are times to tag in an expert. If you smell gas, see scorch marks, or aren’t comfortable handling electrical or plumbing components, stop and call a licensed technician. It’s always better (and cheaper) to fix a small issue early than replace the whole system later.

9. Bonus: Plan Ahead for Replacement

If your water heater is over 10 years old, start budgeting for a replacement. Even a well-maintained tank won’t last forever, and Connecticut’s freezing winters are not kind to aging systems. Newer models are more energy-efficient and often eligible for utility rebates, so upgrading might save you more than you think.

A little attention now keeps the hot water flowing and your winter mornings comfortable. Whether it’s flushing out sediment, tightening valves, or adding insulation, these small steps add up to big peace of mind. 

Bob O’Donnell is the owner of O’Donnell Bros. Inc., a Bristol-based home improvement company established in 1975. Email your questions for Bob to info@odonnellbros.com with the subject line “Ask the Pro.” All questions may be considered for publication. To contact Bob for your remodeling needs, call O’Donnell Bros. Inc. at (860) 589-5155 or visit www.odonnellbros.com. Advice is for guidance only.

Spring Cleaning: Six Tips for Sparkling Windows This Season

After a long, gray Connecticut winter, there’s nothing more satisfying than throwing open the windows and letting in the fresh spring air—unless, of course, your windows are wearing a coat of dirt. Giving your windows a proper cleaning not only improves the view, but it also helps protect your home’s surfaces from buildup and wear. Here are six smart, simple tips to get your windows looking their best this spring:

1. Choose the Right Day

Window cleaning on a sunny day might seem like a good idea, but direct sun can cause your cleaning solution to dry too fast, leaving behind streaks. A cloudy day with mild temperatures is actually best—it gives you more time to wipe before things dry up.

2. Dry Dust First

Before you spray anything, do a quick dry clean. Use a handheld vacuum or a microfiber cloth to remove dirt, cobwebs, and debris from the sills and frames. This stops you from turning dry dust into a muddy mess when the cleaner goes on.

3. Use a DIY Cleaning Solution

Skip the expensive cleaners. For most windows, a 50/50 mix of water and white vinegar does the job beautifully. For extra-tough spots (think kitchen grease or mystery winter smudges), add a small drop of dish soap. It cuts through grime without leaving residue behind.

4. Microfiber or Squeegee—Not Paper Towels

Paper towels can leave behind lint and streaks. Microfiber cloths or squeegees are your best friends here. If you’re using a squeegee, work top to bottom and wipe the blade after each pass to avoid smearing.

5. Clean Those Screens

Window screens take a beating during winter. Remove them and gently scrub with warm, soapy water using a soft brush or sponge. Rinse and let them dry fully before reinstalling. Clean screens not only look better—they also help keep allergens at bay when you open the windows.

6. Inspect While You Clean

Spring cleaning is the perfect time to take a closer look at the condition of your windows. If you’re seeing condensation between panes, cracked frames, or windows that won’t open easily, it might be time to consider replacements. New windows can dramatically improve your home’s energy efficiency and boost resale value—especially in an area like Connecticut, where winters are harsh and heating costs can climb.

A thorough spring window clean instantly brightens your space and makes your whole home feel fresher. It’s a low-cost, high-impact chore that pays off with every sunny day. And if your cleaning routine turns up signs of aging windows, know that replacement is a smart investment for long-term comfort and savings.

Here’s to clearer views and warmer days ahead!

Bob O’Donnell is the owner of O’Donnell Bros. Inc., a Bristol-based home improvement company established in 1975. Email your questions for Bob to info@odonnellbros.com with the subject line “Ask the Pro.” All questions may be considered for publication. To contact Bob for your remodeling needs, call O’Donnell Bros. Inc. at (860) 589-5155 or visit http://www.odonnellbros.com. Advice is for guidance only.

What to Think About When Replacing Your Windows

If your windows are drafty, difficult to open, or outdated, replacing them can be one of the smartest investments you make for your home. New windows not only improve comfort and energy efficiency but can also enhance your home’s curb appeal and resale value. With so many styles, materials, and features available, choosing the right windows can feel overwhelming. Before making a decision, here are several key factors to consider to ensure you get the best results.

1. Energy Efficiency Matters

Windows play a major role in your home’s energy use. If your current windows are old and inefficient, you’re likely losing heat in the winter and cool air in the summer—driving up your energy bills. Look for double or triple-pane glass with Low-E coatings to help regulate indoor temperatures. Insulated frames and argon gas-filled panes also contribute to better energy performance, helping your home stay comfortable year-round while reducing your heating and cooling costs.

2. Consider Your Climate

Connecticut weather can be unpredictable, with cold winters, hot summers, and everything in between. Your windows need to be able to withstand the elements. Vinyl and fiberglass windows are excellent choices for durability, as they resist warping, cracking, and moisture damage. Wood windows offer a classic look but require more maintenance to protect against humidity and temperature changes.

3. Say Goodbye to Drafts

If you frequently feel a chill near your windows, it’s time for an upgrade. Drafty windows not only make your home uncomfortable but also force your heating and cooling system to work harder, increasing your energy bills. High-quality weatherstripping, insulated frames, and multi-pane glass can eliminate drafts and create a more consistent indoor temperature.

4. Protect Your Home from UV Damage

Natural light is great, but too much sun exposure can fade your furniture, flooring, and décor over time. Many modern windows come with UV-resistant coatings that help block harmful rays while still allowing plenty of natural light into your home. This small feature can help preserve your interior and extend the life of your furnishings.

5. Choose the Right Style for Your Home

Replacement windows aren’t just about function—they’re also an opportunity to enhance the look of your home. From traditional double-hung windows to modern casement and picture windows, there are plenty of options to fit your home’s style. Grid patterns, frame colors, and hardware finishes can all be customized to create the perfect aesthetic.

6. Noise Reduction for a Quieter Home

If you live on a busy street or have noisy neighbors, soundproofing might be a priority. Look for windows with multiple panes and insulated frames to help block out unwanted noise, creating a more peaceful indoor environment.

7. Safety and Security Features

Your windows should do more than just look good—they should help keep your home secure. Impact-resistant glass, strong locking mechanisms, and reinforced frames can help protect against break-ins and extreme weather conditions.

8. Professional Installation is Key

Even the best windows won’t perform well if they aren’t installed correctly. Proper installation ensures a snug fit, prevents leaks, and maximizes energy efficiency. Working with an experienced professional guarantees that your new windows will function as intended for years to come.

9. Look for Rebates and Incentives

Energy-efficient windows can qualify for rebates or tax incentives, helping to offset the upfront cost. Check out programs like Energy Star or EnergizeCT to see if you’re eligible for savings when upgrading your windows.

Making the Right Choice

Replacing your windows is a big investment, but it’s one that pays off in home comfort, energy savings, and aesthetic appeal. By considering durability, efficiency, style, and security, you can choose the right windows that will serve your home well for years to come. And when it’s time for installation, don’t cut corners—hire a professional to ensure the job is done right.

Bob O’Donnell is the owner of O’Donnell Bros. Inc., a Bristol-based home improvement company established in 1975. Email your questions for Bob to info@odonnellbros.com with the subject line “Ask the Pro.” All questions may be considered for publication. To contact Bob for your remodeling needs, call O’Donnell Bros. Inc. at (860) 589-5155 or visit www.odonnellbros.com. Advice is for guidance only.