A House That Can Breathe is Crucial To Its Health and Yours

I’m not shy about educating my readers on the importance of proper insulation in a house. But even if you’re one of only 20 percent of homeowners I meet with the right amount of insulation, chances are you’re still missing a critical piece of the puzzle. The missing component is ventilation and not enough of it can be harming both your home and your personal health in more ways than you think. 

In the winter, we crank up the thermostat, sending more heat into our homes than any other time of year. We all know that heat rises, which means a lot of what we’re pumping into the house will quickly find its way through the ceiling and into the attic. Think about when you’re in a car and the windows fog up. What do you do? Usually, you’ll increase the airflow either by using the vents or just cracking a window. A house works much the same way, except that if you don’t have air flowing inside the attic, the heat and moisture just gets stuck there. If the attic is very warm, that moisture will develop into mold and mildew which can feed on your insulation and rot the wood. If the attic is cold enough, the moisture will freeze into little domes or even icicles until the temperature rises enough for the water to thaw and then be absorbed into all the places that it shouldn’t. Neither is a good scenario.

So what’s the best way to protect your home? Start by investing in a hygrometer that measures water vapor in the air. A comfortable humidity reading is 30%-60%, but 45%-55% is an ideal level to maintain. If you’re seeing higher than 60% humidity in any area of your home, it’s going to be susceptible to mold, mildew and bacteria growth.

Remember, attic ventilation allows your house to “breathe” so you want to balance your intake and exhaust to ensure that what is coming in is going out equally. The best ventilation system will include soffit vents that are installed underneath the overhang of the roof and take in the air and ridge vents that are installed at the top of the roof for the hot air to escape. For this method to work efficiently, all louvered vents must be sealed off and you have to ensure that your insulation isn’t blocking the airflow. Believe it or not, most roof manufacturers will void the warranty if a proper ventilation system is not installed. Luckily, new roofing technology enables contractors to add intake ventilation directly into the roof as opposed to using soffit vents, so if you’re in the market for a new roof, be sure to ask for that option. 

It’s important to note that homes have different characteristics and what works well for one may not work well for another. With the right balance of air, homeowners can optimize their roof and maintain the overall health of their home and their families. Remember, it’s always a good idea to get advice from a professional before taking on a big remodeling project. 

Bob O'Donnell is the owner of O'Donnell Bros, Inc., a Bristol-based home improvement company established in 1975. Email your questions for Bob to info@odonnellbros.com with the subject line “Ask the Pro”. All questions may be considered for publication. To contact Bob for your remodeling needs, call O'Donnell Bros, Inc. at (860) 589-5155 or visit www.odonnellbros.com. Advice is for guidance only.

Waterproof Your Chimney for a Leak-Free Winter

You may have never thought about exterior chimney maintenance unless you’ve had a problem, but because chimneys come up above the roofline, they are more susceptible to harsh weather than any other part of your home. That’s why spending a little time and money to waterproof and protect the area can save you thousands of dollars and plenty of potential headaches down the road. 

If you plan on waterproofing your chimney, the first thing you’ll have to do is measure the surface area. Take care to measure all sides and add the measurements together to find the total surface area. This will help you to determine how much material you will need. 

Now, it’s time to clean. Your chimney will most certainly have mold, dirt, rust, and stains on it, and you’ll want to remove them before starting the waterproofing process. I like Chimney RX Safer Brick and Masonry Cleaner which you can use instead of muriatic acid for the same cleaning power without the harsh fumes or risk of burns. Applying the solution is easy: just use one part cleaner with four parts water and apply to the area with a pump sprayer. You can then either scrub the surface or use a power washer to remove the debris. Let everything dry for at least 24 hours before moving on to the next step. 

Next, you can start to prepare the area for any potential repair work. You don't want to damage your roof and shingles when waterproofing your chimney, so use a canvas drop cloth to cover the area as plastic can get very slippery. Make sure to cover over any windows or skylights that are in reach as well. Once waterproofing overspray has been applied, it will be incredibly difficult to remove. 

If you have minor cracks in the chimney, now is the time to fill them. Chimney RX makes a Masonry Crack and Joint Sealant that works really well on small cracks up to one-eighth of an inch. It simply paints on and then dries a milky white color. However, if you have larger cracks or if you need any part of the chimney rebuilt or tuckpointed, I highly suggest calling a professional to manage the repair. 

Once minor work has been completed, you’re ready to apply the waterproofing agent. Again, ChimneyRX makes a great product for the job. No matter what you use, be careful. Most people don’t realize that there is a difference between water repellent and sealant. A sealant will form a hard surface, trapping water inside and making the area susceptible to leaks, whereas a repellent will still enable the porous bricks to breathe and move the way they are supposed to. 

Applying the sealant is as easy as the cleaning step - all you’ll need is a pump sprayer with a fan nozzle. The product that you use will give instructions for the amount that you’ll need, so just go by your surface area and the directions provided. I always suggest starting from the base and working your way up, applying heavy coats using a side to side spraying motion. Unlike painting, it’s a good idea to apply a “flood coat” first and then top it up with a second coat within just a few minutes to even it out. For areas that feel oversaturated, have a soft bristle brush handy. Also, be sure you’re working in good weather - while waterproofing products do dry quickly, you’ll want to give them a good six hours in the sun to fully set before a bout of bad weather. 

Finally, just like any job on a roof, please make sure you’re comfortable with heights and working from a ladder before you tackle this project. The last thing we want is a trip to the emergency room from a nasty fall. When in doubt, always hire a pro to tackle the job.

Bob O'Donnell is the owner of O'Donnell Bros, Inc., a Bristol-based home improvement company established in 1975. Email your questions for Bob to info@odonnellbros.com with the subject line “Ask the Pro”. All questions may be considered for publication. To contact Bob for your remodeling needs, call O'Donnell Bros, Inc. at (860) 589-5155 or visit www.odonnellbros.com. Advice is for guidance only.

Keep Energy Bills Down In Winter With These Tips

Outdoor lights, Christmas trees, and colder temperatures mean that December is usually one of the most expensive months in terms of utility bills. But with the holiday season behind us, January is a great time to take a closer look at how much energy you’re using and address the issues in your home that are causing those high costs. 

One resource that not enough people take advantage of is an energy audit by Energize Connecticut. For a fee, a home energy consultant will come to your home and conduct a full assessment, covering your furnace and water heater, air ducts, windows, doors and more. Plus they can offer rebates for upgrades and repairs. To apply, visit the EnergizeCT website and choose your service provider.

If you’re not in the market for an assessment would still like to enjoy some serious home energy savings, here are the top five spots I always check for air leaks and heat loss. 

1. Windows. Believe it or not, hanging heavy fabric drapes can help you retain up to 25% of the heat in your home. This is especially true with large glass doors that aren’t being used in the winter months. Also, be sure to check for gaps. Wooden window frames get warped with age and can lead to serious air leakage. For cracks that are smaller than a quarter of an inch, a silicone caulk will work to plug up areas where heat is escaping. Also, if you feel air coming right through your single panes and the glass rattles with the wind, beef them up with some shrink film. This product can be found at any home supply store and can be cut to fit any size. 

2. Doors. We don’t often open the windows in the winter, but doors are a different story. They let lots of air escape, but they can’t be sealed completely because we need to use them. I always suggest inspecting your door sweep to ensure it’s not damaged and replacing it if the bristles have come loose. A door snake or seal can also come in handy, which can be purchased at any big box store or even made at home with an old pair of stockings and some rice, beans, newspaper or another filling.

3. Attic. Those of you with an attic hatch are likely losing a ton of warm air through its frame. We all know that hot air rises, so seal up that hatch with heavy duty plastic, or build yourself an insulated box to fit over the entryway if you still need access to storage. 

4. Water Heater. Insulate your water heater’s tank and pipes with fiberglass. For the tank, fit a fiberglass blanket using foil tape, but be sure not to cover any valve or pipe openings. For the pipes, you can use fiberglass wrap or foam insulation. By adding a layer of insulation to your water heater, you’ll keep the warmth from escaping into the air and you’ll protect the machine from condensation in the warmer months. 

5. Insulation. Most homes simply do not have enough insulation in the walls and attic, which is probably the number one contributor to sky-high energy bills. Insulation acts as a barrier against heat flow, helping to keep the warm air inside the house by slowing the flow and stopping the heat from getting outside. The United States Environmental Protection Agency says that with proper insulation, the average home in our area can save approximately 16 to 50 percent in total heating and cooling costs depending on the age and condition of the home. Plus it’s one of the highest rated home improvements in terms of real estate resale value. 

Happy New Year Everyone! Here’s to a warm, happy and healthy 2020!

Bob O'Donnell is the owner of O'Donnell Bros, Inc., a Bristol-based home improvement company established in 1975. Email your questions for Bob to info@odonnellbros.com with the subject line “Ask the Pro”. All questions may be considered for publication. To contact Bob for your remodeling needs, call O'Donnell Bros, Inc. at (860) 589-5155 or visit www.odonnellbros.com. Advice is for guidance only.